YouTube VIDEO
This is the Channel Master wireless programmable 9521A rotor kit which comes with 9537 control box , drive unit , hand unit and power supply. Further down the page is the NTE TB-105 alignment and support bearing
the U-105 $79.95
Precision cut steel gears hardened for long service life
Rugged, one-piece cast aluminium housing designed for greatest strength in high stress areas
Large bearing surface and strong, reinforced mast for lateral load support
Ball bearing provided for thrust ( vertical ) load
High torque- easily handles largest TV/FM antenna
Automatic control; indicator accurately shows orientation of antenna
Control designed for smoother, quieter operation.
Uses 3 conductor rotor wire like CM # 9554
INSTALLATION AND INSTRUCTION SHEET for U105 TV antenna rotor
TB-105 Support Bearing ON SALE $35.95 YouTube VIDEO
OR
To use the TB-105 on the CM or NTE Rotor motor you need to break off the tab that stops the motor from sliding down the pole it is mounted to. The picture above shows the TB105 mounted above a CM rotor motor using a pipe that is about 2" Pole holding the motor and bearing. I am using a 1 1/4" pole up through the bearing. You can use other size poles. Standard poles are 1 1/4"above and below. Maximum is about 2" below and 1 1/2" above.
I have seen comments on line about people saying the bearing does not have enough grease or that it seems that one ball bearings is missing. This is because the TB105 does not need to be built like a high speed bearing is built. A TV rotor only spins at ONE R.P.M. You are using the TB105 to give extra strength to the installation and providing a point to guy above the motor. You mount the TB 105 to save wear on the rotor motor when you are installing a big antenna.
NTE ROTOR PDF also has info on the TB105 at bottom
The New Improved Kindle
Fire's
NTE U-106 Rotor motor with Digital programmable control box with IR hand remote controller
BACK IN STOCK
Features:
DIGITAL DISPLAY CONTROLLER
• Microprocessor controller with 18 functions
• Digital display indicates antenna position during operation
INFRARED REMOTE CONTROL
• 16 function soft-touch key pad remote
• Control antenna directions with the touch of a button from your armchair to change channels easily
Click on link to the left for information about ROKU Box as
low as $79 and free shipping
ROKU HD cm 7400
CM 9521A AUTOMATIC REMOTE CONTROL ROTOR YouTube VIDEO
CM 9521A Automatic programmable TV antenna rotator Sold Out Use NTE U-106 or U-105
.CM's YOUTUBE VIDEO Channel Master Introduction to Rotator
A rotor, or rotator, is a mast-mounted, motor-driven device that permits the TV viewer to conveniently rotate (orient) the outdoor antenna in any direction to optimize reception of a desired TV channel. A rotor should be considered when TV signals are being broadcast from towers in different directions and a single antenna can not accommodate all locations.
A rotator consists of two parts:
1. an indoor control unit
2. an outdoor drive unit.
The two are connected via a 3-conductor wire that carries the voltage and control signals from the indoor unit to the outdoor drive unit.
Channel Master manufactures a remote control unit, model 9521A. A separate indoor controller is also available, model 9537 and is compatible with the following rotator systems: 9500, 9510, 9510A, 9512, 9513, 9515, 9515A, and Radio Shack 15-1225.
IF YOU NEED WIRE, SEE BELOW TO ADD IT TO SHOPPING CART
Model 9537 is the indoor controller and handheld remote control. This model may be added to an existing manual rotator system and instantly upgrades the system to the remote control version.
Back
On Back Order
TV or FM antenna rotor and control that is controlled by a I.R. remote. The control is also able to program up to 69 antenna positions. Now you are able to pre-program the direction to point your antenna which gives you the best reception and go to that position with the touch of a button.CM 9537 is the handheld unit and programmable controller only. Any Channel Master or Radio Shack rotator system can be instantly converted to the remote control version by simply replacing the current control unit with a CM 9537 MORE INFO YouTube Channel Master Introduction to 9537 Rotator Control
Cut to any length you want at a cost of 0.20 per foot
CM 9554-50 round rotor wire 50 ft $10
CM 9554-75 round rotor wire 75 ft $15
CM 9554-100 round rotor wire 100 ft $20
MORE WIRE >>>>>>>
FOR ALL TV ANTENNA PREAMPS (BEST WAY TO IMPROVE YOUR PICTURE QUALITY)>>>
RETURN TO CM INDEX PAGE
FOR MORE ELECTRONIC PRODUCTS
RETURN TO STARKELECTRONIC.COM HOME PAGE with product search
STARK ELECTRONIC
444 FRANKLIN ST. WORCESTER, MA.
TO ORDER PHONE, FAX, OR EMAIL
CALL 508-756-7136 MON-FRI 8:30-5PM EASTERN TIME
WE SHIP UPS ANYPLACE IN USA
SEE OUR NEW CLOSE OUT SALES PAGE
